Calibration Intervals - When is it Time to Recalibrate?

December 12, 2016

Calibration Intervals - When is it Time to Recalibrate?

Since I became involved in the calibration industry in 1972, calibration intervals have been a common topic of interest and confusion.  I was asked to write an article for the newsletter & blog, and after some thought, I determined there was no need.  Many people have published excellent content on the subject:

Calibration Intervals

One of the best and most practical ways for a laboratory to justify calibration, intervals is to maintain Shewhart control charts (SPC – Statistical Process Control charts). This is achieved by monitoring and charting key parameters of the equipment in between currently established calibration intervals for the equipment. Several established control limit criteria are then used to determine the stability of the artifact. This satisfies many requirements for ISO/IEC 17025:2005 ( Dilip Shah’s  “ kill 5 birds with one stone” quotation – the “stone” being the SPC tools and techniques and the “birds” being the ISO/IEC requirements ).

5.5.9  When, for whatever reason, equipment goes outside the direct control of the laboratory, the laboratory shall ensure that the function and calibration status of the equipment is checked and shown to be satisfied before the equipment is returned to service.

5.5.10  When intermediate checks are needed to maintain confidence in the calibration status of the equipment, these checks shall be carried out according to a defined procedure.

5.6.3.3 Intermediate checks

Checks needed to maintain confidence in the calibration status of reference, primary, transfer, or working standards and reference materials shall be carried out according to defined procedures and schedules.

5.9.1  The laboratory shall have quality control procedures for monitoring the validity of tests and calibrations undertaken. The resulting data shall be recorded in such a way that trends are detectable and, where practicable, statistical techniques shall be applied to the reviewing of the results. This monitoring shall be planned and reviewed and may include, but not be limited to, the following:

  1. a) regular use of certified reference materials and/or internal quality control using secondary reference materials;

5.9.2  Quality control data shall be analyzed and, where they are found to be outside pre-defined criteria, planned action shall be taken to correct the problem and prevent incorrect results from being reported.

 

Having the historical data in the SPC format helps to determine and provide justification if the calibration interval needs to be shortened or lengthened. It is also a preventive tool that will help identify issues before they actually become real problems ( ISO/IEC 17025:2005 Clause 4.12 ).

Listed below are links to several articles on calibration intervals for your reference:

ILAC G24

http://www.fundmetrology.ru/depository/04_IntDoc_all/D010-e07.pdf

HBM

http://www.hbm.com/en/3283/guidelines-for-the-determination-of-calibration-intervals/

NIST

http://www.nist.gov/calibrations/recommendedcalibrationinterval.cfm

NCSLI

http://www.ncsli.org/i/i/sp/npb/rp/iMIS/Store/rp.aspx?hkey=bf3e3957-f502-484d-9842-fa5ef6325073

Fluke

http://assets.fluke.com/download/calibration/MSC2009_Deaver.pdf

Quality Digest

http://www.qualitydigest.com/inside/metrology-article/how-optimize-equipment-calibration-intervals.html

ASTM E74 or E2428 from Morehouse
http://blog.mhforce.com/2016/11/top-3-astm-e74-load-cell-calibrations.html

Remember to think of Morehouse for your force and torque calibration needs!

Calibration Intervals - Conclusion

If you enjoyed this article, check out our LinkedIn and YouTube channel for more helpful posts and videos.

Everything we do, we believe in changing how people think about force and torque calibration.  Morehouse believes in thinking differently about force and torque calibration and equipment.  We challenge the "just calibrate it" mentality by educating our customers on what matters, and what causes significant errors, and focusing on reducing them.

Morehouse makes our products simple to use and user-friendly.  And we happen to make great force equipment and provide unparalleled calibration services.

Wanna do business with a company that focuses on what matters most?  Email us at info@mhforce.com.

 

 

# Calibration Intervals

Please share if you found this helpful.

Newsletter Subscription

  • We're committed to your privacy. Morehouse Instrument Company uses the information you provide to us to contact you about our relevant content, products, and services. You may unsubscribe from these communications at any time. For more information, check out our Privacy Policy.

Find Related Articles

When You're Looking for More Accurate Measurements

Morehouse would like the opportunity to earn your business. Contact us today.
Contact Us
  • Type

Top cross
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram